Tips and tricks to repair vertical wood siding

The wood siding gives an elegant and decent look to your house. Moreover, it has a low thermal conductivity which is a terrific feature. It prevents the house from too much heat and cold. There are so many good features of wood siding. 

But it has a dark side too. Because it is an organic product. So, it is susceptible to decomposition. However, to avoid this drawback best quality paint can save the wood siding from decaying for too long. If there is a minor crack in the paint that will allow water to enter. This will ultimately lead to allowing the mold to grow. Likewise, a slight force can crack or break the wood. These drawbacks may seem too dangerous and unable to repair. Fortunately, this is not the case. 

You can protect your wood siding easily by just following some tips and tricks recommended to buy the best roofing services. You need to do the weather-proofing of the siding. You can do this easily with the help of paint, sealant, and caulk. Without any further delay, we want you to know these magical techniques to repair your wood sidings in the best way possible. For this purpose, you just have to do one thing. That specific task is to read this article with concentration. In the end, it will feel like you have already completed your 40% job. So let’s begin the read.

 Mark the damaged part

Like the ageing body, aging houses become problematic. If there is a damaged portion then you do not need to remove the whole board. This is the best advantage of knowing the tricks and tips of repairing siding. This will save your time, energy, and money from excessive work. Look carefully at the damaged area. Take a speed square and place it beneath the damaged area. After that draw a vertical line with a carpenter’s pencil on both sides of the affected area. 

Remove the paint and caulking

To separate the damaged part from the undamaged one, take a utility knife. Cutaway the paint and caulk using the knife. Try to completely break the connection. For this, you have to try several times. Also, try to cut a few inches ahead of the pencil marks cuts.

Vertical cuts

To do this job perfectly, you need an electric multi-tool. This device helps to make a plunge cut. Besides using for repairing, this tool is very essential for many doing improvements. As it is a handy tool, you must buy one. It will be a one-time purchase and you will become able to do a lot of work with it. 

You need to fit the wood blade onto the multi-tool. Put on your safety glasses and a dust mask. Now, after taking all the precautionary measures, turn on the multi-tool. At this step, you need to be very careful. Try not to cut more than your requirement. Pay close attention and turn off the multi-tool to avoid excessive cutting. 

Remove the nails

Look at the gaps. Now, take a pry bar. Force it into the gaps between the undamaged and damaged parts. Rock the pry bar back and forth to remove the nails. This will help you to pull the heads of the nails protrude out. Now, take a hammer and remove the nail with the help of the claw section of the hammer. At this point, the damaged siding is completely loose. Remove it. 

New siding

For cutting a new siding, you need a model or template. Use the removed siding as a template. This will help you to mark the exact size and dimension of the new siding board. Take an electric miter saw and cut the new siding.

Fix the new siding

After cutting the new siding according to the template, slide the new siding board upward, underneath its top siding board. Make the siding board flat. Locate the already present nail holes. Nail the new siding board by driving nails into the previously existing holes in the upper board. This will help you to initially adjust the board.

To fix it properly, drive a few more nails on the top board. Now fix the bottom of the new siding board by driving nails into the top of the underneath board and as well as at the bottom of the new board simultaneously. 

This process will help you to fix the new siding board with the top and bottom boards.

Paint and caulk

First, you have to caulk the entire horizontal seams among the boards. Now, to inject the caulk in the vertical seams inject the caulk in the seam. Now, tap and rub with your fingers to fill the seam with the caulk. 

After caulking the new siding board, choose the paint which you want to apply. In most cases, it is the same paint which is already applied to the remaining siding. As the replaced siding board is a new part, you must apply a minimum of two coats. First, apply the first coat. Let it dry completely. After that, apply the second coat of the paint. Moreover, if you want you can also apply the third coat of the paint. 

Leave a Reply

Your email address will not be published. Required fields are marked *